Caravan Spring Choices

Caravan spring choices help prevent holiday accidents. I hope this helps you when making your trailer spring selection.

Yes, these matters are serious, and you will need professional help unless you happen to be an engineer or a tradesperson who understand a little basic engineering.

Yes, your car will stop your caravan but not in an emergency situation.

The information below may seem difficult to read but keep coming back to it as it is a good reference point for learning later.

When in doubt, call our sales team on 0733483822, Bruce, Mike or Christopher. We will be happy to discuss how you can make your rig safe and secure for the next big trip. We recommend getting a weighbridge certificate so we can give you the correct information.

Weighbridge Certificate

The best place to start caravan upgrade work is with a weighbridge certificate. This certificate allows you to correctly select the following components.

  • Springs
  • Axles
  • Coupling
  • Tyres – gives you correct information about right tyre pressure.
  • You will also need a tow ball scale so you can add the tow ball weight to your weighbridge certificcaravan springate.

Rocker Roller Springs

Rocker roller springs would be the most commonly used caravan springs on trailers today.

However, foresight must be used to correctly select your spring size. Select a spring capacity about 10% over your weighbridge certificate.

Planning for the future and shock loading conditions will help you significantly avoid disasters.

There are many rocker roller springs on the market so let’s look at the best of them. The spring on the right uses the second leaf as a wrap. This wrap restricts the expansion of leaf #1 under extreme loading conditions.

trailer springLeaf #3 is located 80mm from the eye and support loads 80mm from the eye. Note: This is the breakage point so it is important this spring is located in this position.

Leaf #4 is located 100mm from the eye and supports leaf #3. If you leaves are further apart, we recommend selecting another brand of spring. Al-ko or Couplemate.

Roller End of the spring has leaf #3 directly under the roller and 100mm from the end of the spring. Leaf #3 is the most important of the spring set because it is the foundation of the load capacity of the suspension.

melbourne trailer springs

Couplemate now carries springs for G&S Chassis caravans and Melbourne Trailer Caravans. 

I have put a link to the product in the name, so if you click the name above, you will be taken to the spring you wish to purchase.

Axle loadings

Your trailer springs will be selected according to maximum axle loadings. Axle loadings are

  • 750kg – 39mm Round LM bearings.
  • 1000kg – 40mm Square LM bearings.
  • 1450kg – 45mm Round slimline bearings.
  • 1450kg – 45mm Square slimline bearings.
  • 1600kg – 45mm Square Parallel bearings.
  • 2250kg Square depending on bearings used.

The lowest common denominator calculates caravans and trailers weight ratings. It is the bearings used that determine axle rating.

Upgrade your caravan spring not exceed your axle capacity.

Exceeding Axle Capacity

Let’s say you choose to put six leaf shackle springs (1500kg) on a 39mm Round Axle.

Yes, they fit but are not suitable to carry your desired load.

Although this axle can carry the weight short-term, your caravan springs will flex causing premature ageing and failure. Your axle will also snap under stress loading due to vibration fatigue.

Premature Ageing and Failure

Now you have assembled your 1500kg springs onto your 39mm Round Axle and loaded your trailer ready for that trip to Cape York.

Now run a straight edge across that axle. See the gap between the straight edge and the axle in the middle of the beam?

If the gap is greater than 5mm, you are in trouble, and your entire rig will fail.

The axle will wobble up the highway, creating reverberations to your springs. The stresses if not dampened are going to your springs from your axle and causing premature ageing.

caravanThese stresses are released through your bearings, so you also have extreme bearing wear.

Now hit a pothole on the shoulder of the road and your outer bearing snaps.

So let’s go back to square one and do it right. Talk to the experts at Couplemate.

Caravan Spring or Axle upgrade

2200mm x 45mm Square Parallel Axle

If you are upgrading more than your axle rating without checking your components attached to the axle, then a problem can occur. Let’s go through a few things you need to remember.

Correct axle selection will save you money on bearings, springs and other running costs.

Problems occur when your fully loaded caravan is almost the same capacity as your maximum carry load.

If you are over your maximum carrying load limit, then you are at the stage of an axle and brake upgrade.


Small springs may have 6mm fish plates so upgrade those to 8mm. Off-Road springs have 10mm fishplates.  Care should be taken when tightening U-bolts, too much tension on one side may cause spring breakage.

It is extremely important that you tighten the u-bolts coming through your fish-plate evenly. Uneven tightening will cause your spring to crack and eventually break in the middle.


U-bolts will be tight when you first install them. However, they are known to stretch after 500 km. Give them a re-tighten.

ubolt test rigWe recommend and use nylock nuts on all of our u-bolts. Couplemate Trailer Parts supply the only know rated u-bolt on the Australian market.

Due to known failures in u-bolts manufactured in various countries, Couplemate batch tests every shipment. U-bolt failure is commonly known as hydrogen embrittlement and is caused by the tension caused by bending. We remove this stress by further baking u-bolts in ovens after the bending process.

The breaking capacity of Couplemate u-bolts are

  • 1/2 inch – 17 tonne
  • 5/8 inch – 23 tonne

So not all u-bolts are the same nor should you rely on the cheapest u-bolt being the best quality for you.

Couplemate u-bolts are premium and as such are tested and guaranteed. You may pay a few cents more. However, you can be certain that your u-bolts have been well designed, tried and tested long before your purchase.

Make sure your U-bolts holding your springs have not rusted and are tight. Loose U-Bolts have been known to break your springs. It is very common for springs to rust in between the leaf. If you are dipping your springs in salt water and they are not galvanised, then you will get 4 – 5 years life out of your springs.

Trailer Spring Choices

Spring loading capacity must be known when you purchase your springs so have a look at your axle size first. Note: Not all springs are the same, choose a good brand spring.

If your dealer cannot tell you the spring capacity, please walk out of the shop. Loaded spring rating is the first test of competence.

If your trailer total weight is say 800kg, and you have a 45mm axle, please do not put six leaf springs in because it is over-kill. Your trailer will bounce all the way down the highway. Try and match your average loads exactly with your spring setup to ensure trouble-free trailering. Better to have the right springs on a heavier axle.

Eye to eye springs is common for campers, tandems, box trailers and some caravans.

Off-road springs are heavier again and are suited to campers. Why? Because Caravan and Camper springs are 60mm wide as opposed to 45mm for standard spring setup. 60mm wide springs are more durable and can handle extreme loads of tandem trailers when cornering.

Slipper springs are standard on boat and Jet Ski trailers.

If you are going into some really big spring systems, then go for off-road or rocker roller type suspension systems. Rocker Roller spring systems give a better ride than standard tandem suspension system.

Should I put my springs under my axle to gain extra lift?

Here are examples of what not to do.

  1. 39mm Axle (750kg) with four left slipper springs (800kg). This system is ok, but often it is tempting to put six leaf springs (1300kg) on this axle thinking it is also OK. Unfortunately, you will break many sets of slippers in 12 months. Why? Because a lot of axle flexing occurs when axles are overloaded. This flex causes rapid deterioration of the springs, and they are breaking due to fatigue. Upgrade your axle to 40mm Square or 45mm Round Axle which will cost you about $80.
  2. Another bloke wanted six stud Landcruiser hubs on his boat with a 39mm axle. Same problem, broken springs. You need to de-rate axles and springs by 20% when using six stud Landcruiser hubs because of the bigger wheel, more weight and more pressure on the axle setup. Again he needs to upgrade his axle.
  3. Another bloke had a 50mm Round Axle with a 4.2mtr boat and wanted six leaf springs. Seems OK but the boat was too light for this heavy setup, which would have resulted in it skipping through corners and bouncing down the highway.
  4. Don’t sandblast springs. Measure the width of the spring at the spring centre bolt. If the width has grown either side of the spring centre bolt, then your spring has cancer and needs to be replaced.
  5. Do not put slipper springs on your camper. Under extreme conditions, the slipper springs can dislodge itself from it a rear hanger. Campers, especially off-road campers use eye to eye springs. Campers with slipper springs are restricted to on-road use for problem free motoring.

Camper Trailer Spring Choices

  • Off-road campers usually take a pounding in comparison to their bitumen only cousins.
  • Off-road outback rebound springs are a must with 5/8″ U-Bolts. 1/2″ U-Bolts are normally installed on all trailers, but you need the larger U-Bolts when you are trying to kill your suspension in rugged country.
  • Outback springs are 60mm Wide and cater for a fair whack due to twisting and turning in all sorts of terrain. Normal 45mm wide springs are going to give you trouble soon or later.
  • Axle width should be no less than 45mm Round or 45mm Square. Brake your trailer with either electric off-road or disc override rotors.
  • Off-road electrics are the preferred favourite over standard electric brakes. Standard brakes cannot handle the dust and heat associated with off-road warriors but are commonly used by the bitumen dwellers. There is also an issue with magnet rattle; off-road magnets have plastic bushes to help prevent magnet arm failure.

Tandem Springs

Question: Where do I locate the middle hanger bracket?

Answer: Rule of thumb is to measure the box length of your chassis. 1 inch to 2 feet of the length is the distance from the centre to the back of the trailer where the centre rocker is hung. Boat trailers are heavier in the rear than a camper, so the rule varies a little.

The best tandem springs can be purchased here.

Example, if the measurement is 12′, then  12/2 = 6 inches back of centre.